JOI 2026 EN

9M SILR Y for Helix 59 7676 14M ID SILR Y for Solix and Apex 59 7688 9-M360-2DDI-Y 59 7668 14-M360-2DDI-Y 59 7669 PC 12 ST SOLIX and ONIX 59 7679* AS T Y HELIX 5, 7, Series 600 HD, 700 HD, 8x9ci, 9x9ci, 11x9ci 59 7673 CABLE SWITCHES FOR SI / MEGA SI TRANSMITTERS CABLE SWITCHES FOR MEGA 360 CABLE SWITCH FOR SPEED SENSOR Side Imaging left – right splitter cable If one of the two side beams is obstructed, e.g., by the hull shape or the motor, this cable can be used to connect a second SI transmitter, so that one is responsible for the left side of the boat and the other for the right side. No switching is necessary; left/right is automatically detected by the pin assignment. Please note: The two Y-cables below are used to connect Mega 360 and any Mega Imaging(+) transmitters. Please note that if a Mega SI(+) transmitter is connected to this Y-cable, the SI function of this transmitter must be switched off. The SI function is taken over by the Mega 360, with a shorter range. Only the DI and HW Dual Spectrum data from the SI sensor is processed. It therefore makes more sense to connect a Mega DI(+) sensor to one of the two Y-cables next to the Mega 360 and to have any SI sensors in the network processed by another device. Mega 360 14-pin - Mega Imaging+ 7-pin sensor splitter cable For connecting the above encoders to a Helix Mega Imaging+ device. Mega 360 14-pin - Mega Imaging(+) 14-pin sensor splitter cable Mega Imaging(+) transducers include not only those from the Humminbird SOLIX device series, but also the MDI and MSI transducers built into our MINN KOTA motors. This means that this splitter cable can be used not only for SOLIX devices but also for HELIX devices, but with a 14-to- 7-pin adapter cable (included with Mega 360, 3 m). This Y-cable is used to connect a temperature and speed sensor to your Humminbird device. No additional cable is required for Helix 8-12 and Series 1100, 900/800. COLLECTOR PLUG FOR HELIX You want your Helix to be flexible and Using multiple boats? Then use the prac t i cal connector. Transmitters, network cables , etc. remain connected to the con- nector; only the connection to the Helix needs to be disconnected or connected. Compatible with Helix 8-15 HCCT 59 7615 Y-CABLE Errors and technical changes reserved | *While stocks last! for 7-pin echo sounder transducers Order No. EC M10 3m 59 7548 EC M30 9m 59 7546 for 14-pin echo sounder transducers Order No. EC M3 14W30 3m Mega 360 and Minn Kota Mega trans- ducers 59 7537 EC M3 14W30 9m Mega 360 and Minn Kota Mega trans- ducers 59 7531 EXTENSION CABLE FOR ENCODERS Extend the cable between Transducer for your Humminbird fish finder for Helix fishfinders for Solix and Apex fishfinders POWER CABLE Order No. PC-10 1.8 m: for Helix 5-7 except SI and DI devices, Phiranha Max 59 7552 PC-11 1.8 m with interference filter: for Helix 5-7 with SI or DI, Helix 8-15, and series 1100, 900, 800 59 7562 PC-12 1.8 m: for SOLIX and ONIX 59 7559 PC-13 1.8 m: for APEX, XPLORE, and MEGA Live 1 & 2 59 7557 60 HUMMINBIRD ACCESSORIES 9M SIDB Y for Helix 59 7677 14M SIDB Y for Solix 59 7680* 14M ID SIDB Y for Solix and Apex 59 7687 Side Imaging – Dual Beam Transducer Splitter Cable Combine the Side Imaging transducer and the Dual Beam transducer for better bottom detection at high speeds. No switch is required. for Helix for Solix & Apex HUMMINBIRD HDMI CABLE FOR APEX HDMI IN Length 3m 59 xxxx HDMI OUT Length 3m 59 xxxx